U1172: Invalid/Missing Remote Button Control Data
Complete diagnostic information, symptoms, and potential causes
Manufacturer-Specific Variations
This code (U1172) may have different meanings or additional parameters depending on your vehicle's make, model, and year. Network communication codes (U-codes) are particularly manufacturer-specific and may require specialized diagnostic tools. Always verify with your vehicle's service manual or a qualified technician before attempting repairs.
Invalid/Missing Remote Button Control Data
Description
SCP (J1850) Invalid or Missing Data for Remote Button Control. Check steering wheel switches, remote module, and network communication.
Common Symptoms
- Inoperative steering wheel controls (audio, cruise control, etc.) [citation:3]
- Remote key fob features (door lock/unlock, trunk release) not responding [citation:3]
- Loss of horn or radio control from steering wheel [citation:3]
- Intermittent or delayed system response [citation:3]
- No apparent warning lights, or general communication fault message on dashboard [citation:3]
Possible Causes
- Faulty or loose wiring/connectors in SCP (J1850) data bus circuit [citation:3]
- Faulty Remote Button Control module (steering wheel switches or remote receiver) [citation:3]
- Network communication interruption due to corrosion or poor ground [citation:3]
- Malfunctioning Body Control Module (BCM) or Gateway Module [citation:3]
- Software errors or outdated firmware in networked modules [citation:3]
- Aftermarket accessory interference (alarm, stereo upgrades) [citation:3]
Diagnosis Steps
- IDENTIFY MANUFACTURER FIRST - Ford, Lincoln, Mercury, or Mazda vehicles [citation:3].
- Start with visual inspection of all wiring and connectors related to Remote Button Control and SCP (J1850) bus [citation:3].
- Check for corrosion, loose pins, or damaged connectors on steering wheel, remote module, and junction boxes [citation:3].
- Use diagnostic scan tool to access all related modules and verify if other communication codes are present [citation:3].
- Test continuity and resistance of SCP (J1850) wires using multimeter [citation:3].
- If wiring checks out, attempt to clear code and operate remote controls to see if code returns [citation:3].
- If available, perform network test or module self-test via scan tool [citation:3].
- If fault persists, substitute or reprogram suspected modules as advised by OEM [citation:3].
Repair Solutions
- Repair or replace damaged wiring/connectors on SCP (J1850) bus [citation:3]
- Replace faulty Remote Button Control module or steering wheel switch assembly [citation:3]
- Clean or repair corroded grounds or junction points [citation:3]
- Update or reflash software in affected modules as per OEM bulletins [citation:3]
- Remove or rewire aftermarket accessories interfering with data bus [citation:3]
- Replace BCM or Gateway Module if confirmed defective after all other steps [citation:3]
Prevention Tips
- Check battery health first - low voltage can trigger this code [citation:3]
- Do not replace module without inspecting wiring and connectors [citation:3]
- Check for related codes in other modules (network faults often cluster) [citation:3]
Working with ECU firmware? Remove DTCs directly from firmware files
Our free Firmware DTC Remover detects and removes hardcoded fault codes directly from ECU firmware files — no software needed. Supports BMW / MINI, VAG (VW, Audi, Porsche, Skoda, Seat, Cupra), PSA (Peugeot, Citroën, DS), Mercedes-Benz, Renault / Dacia / Samsung, Ford, Kia / Hyundai, Land Rover / Jaguar (EDC16, EDC17, MD1, MEVD17, MSV/MSD (7X/8X/9X), MS45, DCM3.7, DCM6.x, PCR2.1, DCM3.4, SID201, SID208, SID803/803A, CRD1.xx, CRD2.xx, CRD3.xx, SID3xx, SID202-SID206, SID209-SID211, DCM3.5, EMS22xx, EMS24xx (test), SIM210 (test), SIM28/29 (test), DCM3.2, SIM2K, SID20x, MED17). Free: 3 removals/day.