U1185: Invalid Wiper/Washer Data / SCP Network Fault

Complete diagnostic information, symptoms, and potential causes

⚠️

Manufacturer-Specific Variations

This code (U1185) may have different meanings or additional parameters depending on your vehicle's make, model, and year. Network communication codes (U-codes) are particularly manufacturer-specific and may require specialized diagnostic tools. Always verify with your vehicle's service manual or a qualified technician before attempting repairs.

U1185
Network Communication Code

Invalid Wiper/Washer Data / SCP Network Fault

Network CommunicationsMEDIUM👁 Views: 40

Description

Manufacturer-specific: VAG invalid wiper/washer data or Ford/Lincoln/Mercury/Mazda/Jaguar/Land Rover wiper/washer communication fault

Common Symptoms

  • Check Engine Light
  • FOR VAG: Invalid or missing data for wiper/washer
  • Intermittent or non-functioning windshield wipers
  • Washer fluid does not spray when activated
  • Wipers only operate at one speed or in one mode
  • Delayed response to wiper/washer controls

Possible Causes

  • FOR VAG: Missing or corrupted data on CAN bus
  • FOR VAG: Faulty gateway module
  • Faulty or corroded connectors at wiper/washer module or BCM
  • Open or shorted wiring in data bus circuit
  • Defective window wiper/washer module or switch
  • Issues with Body Control Module (BCM)
  • Low system voltage or weak battery causing intermittent communication loss

Diagnosis Steps

  1. IDENTIFY MANUFACTURER FIRST - VAG or Ford/Lincoln/Mercury/Mazda/Jaguar/Land Rover context
  2. FOR VAG: Use professional diagnostic tool (VCDS/ODIS) for accurate description
  3. FOR VAG: Check CAN bus wiring and gateway module operation
  4. Verify code with scan tool and check for related DTCs
  5. Visually inspect wiring and connectors at wiper/washer module, BCM, and junction points
  6. Check battery voltage and charging system health
  7. Use wiring diagram to test continuity and resistance on SCP bus
  8. Monitor live data with scan tool for module communication

Repair Solutions

  • FOR VAG: Update software in affected modules
  • FOR VAG: Repair CAN bus wiring issues
  • FOR VAG: Replace faulty gateway module
  • Clean or replace corroded connectors and terminals
  • Repair damaged wiring in SCP data bus circuit or ground points
  • Replace faulty wiper/washer switch or module
  • Repair or replace Body Control Module (BCM)
  • Resolve battery or charging system issues

Prevention Tips

  • Always verify manufacturer before diagnosis
  • Use professional diagnostic tools for accurate diagnosis
  • Check battery health first
  • Don't replace module without checking wiring
⚡

Working with ECU firmware? Remove DTCs directly from firmware files

Our free Firmware DTC Remover detects and removes hardcoded fault codes directly from ECU firmware files — no software needed. Supports BMW / MINI, VAG (VW, Audi, Porsche, Skoda, Seat, Cupra), PSA (Peugeot, Citroën, DS), Mercedes-Benz, Renault / Dacia / Samsung, Ford, Kia / Hyundai, Land Rover / Jaguar (EDC16, EDC17, MD1, MEVD17, MSV/MSD (7X/8X/9X), MS45, DCM3.7, DCM6.x, PCR2.1, DCM3.4, SID201, SID208, SID803/803A, CRD1.xx, CRD2.xx, CRD3.xx, SID3xx, SID202-SID206, SID209-SID211, DCM3.5, EMS22xx, EMS24xx (test), SIM210 (test), SIM28/29 (test), DCM3.2, SIM2K, SID20x, MED17). Free: 3 removals/day.

Try DTC Remover — Free →