U1184: Invalid Wiper/Washer Data / SCP Network Fault

Complete diagnostic information, symptoms, and potential causes

⚠️

Manufacturer-Specific Variations

This code (U1184) may have different meanings or additional parameters depending on your vehicle's make, model, and year. Network communication codes (U-codes) are particularly manufacturer-specific and may require specialized diagnostic tools. Always verify with your vehicle's service manual or a qualified technician before attempting repairs.

U1184
Network Communication Code

Invalid Wiper/Washer Data / SCP Network Fault

Network CommunicationsMEDIUM👁 Views: 16

Description

Manufacturer-specific: VAG invalid wiper/washer data or Ford/Lincoln/Mercury SCP network fault - verify manufacturer first

Common Symptoms

  • Check Engine Light
  • FOR VAG: Invalid or missing data for wiper/washer
  • Windshield wipers not responding to switch commands
  • Wipers operating intermittently or unexpectedly
  • Washer fluid not spraying when requested
  • Intermittent or total loss of wiper/washer function

Possible Causes

  • FOR VAG: Missing or corrupted data on CAN bus
  • FOR VAG: Faulty gateway module
  • Faulty or loose wiring/connectors at wiper/washer module or BCM
  • Malfunctioning wiper/washer control module
  • Corroded or dirty connector terminals
  • Software glitches in module or vehicle network
  • Network (bus) faults such as shorts or opens in SCP wiring

Diagnosis Steps

  1. IDENTIFY MANUFACTURER FIRST - VAG or Ford/Lincoln/Mercury context
  2. FOR VAG: Use professional diagnostic tool (VCDS/ODIS) for accurate description
  3. FOR VAG: Check CAN bus wiring and gateway module operation
  4. Verify U1184 and check for other related codes with scan tool
  5. Consult OEM wiring diagrams for wiper/washer and SCP network circuits
  6. Physically inspect all relevant connectors for corrosion, looseness, damage
  7. Test for continuity and proper voltage at key points
  8. Check integrity of grounds shared by wiper/washer module and network

Repair Solutions

  • FOR VAG: Update software in affected modules
  • FOR VAG: Repair CAN bus wiring issues
  • FOR VAG: Replace faulty gateway module
  • Repair or replace damaged/corroded wiring/connectors in wiper/washer circuit
  • Clean and secure all related electrical connectors
  • Replace wiper/washer control module if it fails checks
  • Update or reflash module software per OEM bulletins

Prevention Tips

  • Always verify manufacturer before diagnosis
  • Use professional diagnostic tools for accurate diagnosis
  • Check connectors before suspecting modules
  • Address wiper issues promptly for safety
⚡

Working with ECU firmware? Remove DTCs directly from firmware files

Our free Firmware DTC Remover detects and removes hardcoded fault codes directly from ECU firmware files — no software needed. Supports BMW / MINI, VAG (VW, Audi, Porsche, Skoda, Seat, Cupra), PSA (Peugeot, Citroën, DS), Mercedes-Benz, Renault / Dacia / Samsung, Ford, Kia / Hyundai, Land Rover / Jaguar (EDC16, EDC17, MD1, MEVD17, MSV/MSD (7X/8X/9X), MS45, DCM3.7, DCM6.x, PCR2.1, DCM3.4, SID201, SID208, SID803/803A, CRD1.xx, CRD2.xx, CRD3.xx, SID3xx, SID202-SID206, SID209-SID211, DCM3.5, EMS22xx, EMS24xx (test), SIM210 (test), SIM28/29 (test), DCM3.2, SIM2K, SID20x, MED17). Free: 3 removals/day.

Try DTC Remover — Free →