U1170: Invalid/Missing Cellular Phone / Paging System Data
Complete diagnostic information, symptoms, and potential causes
Manufacturer-Specific Variations
This code (U1170) may have different meanings or additional parameters depending on your vehicle's make, model, and year. Network communication codes (U-codes) are particularly manufacturer-specific and may require specialized diagnostic tools. Always verify with your vehicle's service manual or a qualified technician before attempting repairs.
Invalid/Missing Cellular Phone / Paging System Data
Description
SCP (J1850) Invalid or Missing Data for Cellular Phone / Paging System. Check telematics module, wiring, and network communication.
Common Symptoms
- Malfunction or unavailability of built-in cellular phone or telematics system [citation:1]
- Warning messages or "no phone detected" alerts on dashboard or infotainment display [citation:1]
- Loss of remote services (remote unlock, emergency call features) [citation:1]
- Occasional chimes or error tones after startup [citation:1]
- Other communication DTCs stored in related modules [citation:1]
Possible Causes
- Faulty or disconnected cellular phone/paging module [citation:1]
- Damaged, corroded, or loose wiring/connectors at module or along SCP (J1850) network [citation:1]
- Aftermarket equipment installation disrupting factory communication bus [citation:1]
- Network-wide issues such as short or open circuit on SCP (J1850) data line [citation:1]
- Failed or outdated software in telematics or body control module [citation:1]
- Blown fuse or insufficient power/ground to module [citation:1]
Diagnosis Steps
- IDENTIFY MANUFACTURER FIRST - Ford, Lincoln, Mercury, Mazda, or Jaguar vehicles [citation:1].
- Verify code with scan tool and note any additional DTCs in other modules [citation:1].
- Check if cellular/telematics system is present and enabled (not all vehicles are equipped) [citation:1].
- Inspect all related fuses and relays for telematics/phone system [citation:1].
- Examine physical connections at cellular/paging module for corrosion, bent pins, or loose connectors [citation:1].
- Check SCP (J1850) wiring for continuity, shorts, or signs of damage, especially if aftermarket equipment installed [citation:1].
- Use scan tool to attempt communication with affected module [citation:1].
- Test power and ground supplies at module using multimeter [citation:1].
- If wiring checks out, consider reprogramming or updating telematics/module software per OEM [citation:1].
- Replace module only after confirming all other steps [citation:1].
Repair Solutions
- Reconnect or replace loose, corroded, or damaged wiring/connectors [citation:1]
- Replace blown fuses or restore proper power/ground to module [citation:1]
- Remove or correctly integrate aftermarket equipment interfering with communication bus [citation:1]
- Update or reflash telematics/module software as per OEM instructions [citation:1]
- Replace cellular phone/paging module if confirmed faulty [citation:1]
- Repair or replace sections of SCP (J1850) data line if wiring faults found [citation:1]
Prevention Tips
- Do not replace module without checking power, ground, and network wiring first [citation:1]
- Always check for other related communication codes that may provide valuable clues [citation:1]
- Inspect connectors for corrosion even if they "look clean" [citation:1]
Working with ECU firmware? Remove DTCs directly from firmware files
Our free Firmware DTC Remover detects and removes hardcoded fault codes directly from ECU firmware files — no software needed. Supports BMW / MINI, VAG (VW, Audi, Porsche, Skoda, Seat, Cupra), PSA (Peugeot, Citroën, DS), Mercedes-Benz, Renault / Dacia / Samsung, Ford, Kia / Hyundai, Land Rover / Jaguar (EDC16, EDC17, MD1, MEVD17, MSV/MSD (7X/8X/9X), MS45, DCM3.7, DCM6.x, PCR2.1, DCM3.4, SID201, SID208, SID803/803A, CRD1.xx, CRD2.xx, CRD3.xx, SID3xx, SID202-SID206, SID209-SID211, DCM3.5, EMS22xx, EMS24xx (test), SIM210 (test), SIM28/29 (test), DCM3.2, SIM2K, SID20x, MED17). Free: 3 removals/day.