U11B9: Multi-Manufacturer: U11B9 (RF Hub / BMU / Volume Control)

Complete diagnostic information, symptoms, and potential causes

⚠️

Manufacturer-Specific Variations

This code (U11B9) may have different meanings or additional parameters depending on your vehicle's make, model, and year. Network communication codes (U-codes) are particularly manufacturer-specific and may require specialized diagnostic tools. Always verify with your vehicle's service manual or a qualified technician before attempting repairs.

U11B9
Network Communication Code

Multi-Manufacturer: U11B9 (RF Hub / BMU / Volume Control)

Network CommunicationsMEDIUM👁 Views: 18

Description

U11B9 indicates Chrysler RF Hub communication loss, Mitsubishi EV battery unit fault, or VAG volume control issue.

Common Symptoms

  • FOR VAG: Steering wheel volume controls not working, audio system issues
  • FOR CHRYSLER: Keyless entry malfunction, remote start inoperative, TPMS issues ("--" display on dash) [citation:2][citation:8]
  • FOR MITSUBISHI EV: EV system warnings, potential battery management faults [citation:5]

Possible Causes

  • FOR CHRYSLER: CAN bus circuits open or shorted, RF Hub power/ground issues, BCM configuration incorrect, faulty RF Hub [citation:2]
  • Battery voltage must be 10-16V, messages not received for 2-5 seconds [citation:2]
  • FOR MITSUBISHI: BMU (SUB) failure - signal sent by BMU through CAN cannot be received [citation:5]

Diagnosis Steps

  1. IDENTIFY MANUFACTURER FIRST.
  2. FOR CHRYSLER: Use scan tool to check for related DTCs (battery voltage, ignition, VIN messages) [citation:2].
  3. Check RF Hub power and ground circuits.
  4. Verify BCM configuration is correct [citation:2].
  5. Test CAN bus circuits for opens or shorts.
  6. For 2013+ RAM trucks, note that RF Hub processes TPMS signals - U11B9 can cause TPMS warnings [citation:8].
  7. FOR MITSUBISHI: Erase DTC - if past trouble, diagnosis may not be needed [citation:5].

Repair Solutions

  • FOR VAG: Replace volume control module or repair steering wheel wiring.
  • FOR CHRYSLER: Repair CAN bus circuits, restore power/ground to RF Hub, correct BCM configuration, replace RF Hub [citation:2].
  • FOR MITSUBISHI: Replace sub-battery management unit [BMU (SUB)] if fault persists [citation:5].

Prevention Tips

  • For Chrysler vehicles with TPMS issues, check for U11B9 - indicates RF Hub communication failure
  • Battery voltage must be within 10-16V for proper RF Hub operation [citation:2]
⚡

Working with ECU firmware? Remove DTCs directly from firmware files

Our free Firmware DTC Remover detects and removes hardcoded fault codes directly from ECU firmware files — no software needed. Supports BMW / MINI, VAG (VW, Audi, Porsche, Skoda, Seat, Cupra), PSA (Peugeot, Citroën, DS), Mercedes-Benz, Renault / Dacia / Samsung, Ford, Kia / Hyundai, Land Rover / Jaguar (EDC16, EDC17, MD1, MEVD17, MSV/MSD (7X/8X/9X), MS45, DCM3.7, DCM6.x, PCR2.1, DCM3.4, SID201, SID208, SID803/803A, CRD1.xx, CRD2.xx, CRD3.xx, SID3xx, SID202-SID206, SID209-SID211, DCM3.5, EMS22xx, EMS24xx (test), SIM210 (test), SIM28/29 (test), DCM3.2, SIM2K, SID20x, MED17). Free: 3 removals/day.

Try DTC Remover — Free →