P0986: Shift Solenoid E Control, Signal too High

Complete diagnostic information, symptoms, and potential causes

⚠️

Manufacturer-Specific Variations

This code (P0986) may have different meanings or additional parameters depending on your vehicle's make, model, and year. Always verify with your vehicle's service manual or a qualified technician before attempting repairs.

P0986
Powertrain Code

Shift Solenoid E Control, Signal too High

Transmission Control SystemMEDIUM👁 Views: 66

Description

Shift Solenoid E Control, Signal too High

Common Symptoms

  • Check Engine Light for shift solenoid E signal too high
  • Excessive shift solenoid E signals
  • Transmission shift overvoltage warnings
  • Gear selection protection errors for solenoid E
  • Hydraulic valve regulation E problems

Possible Causes

  • Overvoltage supply to shift solenoid E
  • Solenoid E output signal excessive
  • Short circuit in shift solenoid E wiring
  • Shift solenoid E internal short circuit
  • Voltage regulator problems for shift solenoid E

Diagnosis Steps

  1. Check shift solenoid E signal for overvoltage
  2. Verify voltage supply to shift solenoid E not excessive
  3. Test for shorts in shift solenoid E circuit
  4. Check shift solenoid E internal resistance
  5. Verify voltage regulation for shift solenoid E
  6. Test reference voltage to shift solenoid E

Repair Solutions

  • Fix overvoltage supply to shift solenoid E
  • Replace shift solenoid E with excessive output
  • Repair short circuit in shift solenoid E wiring
  • Replace shift solenoid E with internal short
  • Fix voltage regulator problems for shift solenoid E
  • Correct faulty reference voltage to shift solenoid E

Prevention Tips

  • Monitor shift solenoid E signals for overvoltage
  • Maintain proper voltage regulation
  • Check for wiring shorts regularly
  • Address excessive signals immediately
  • Protect shift solenoid circuits from overvoltage
⚡

Working with ECU firmware? Remove DTCs directly from firmware files

Our free Firmware DTC Remover detects and removes hardcoded fault codes directly from ECU firmware files — no software needed. Supports BMW / MINI, VAG (VW, Audi, Porsche, Skoda, Seat, Cupra), PSA (Peugeot, Citroën, DS), Mercedes-Benz, Renault / Dacia / Samsung, Ford, Kia / Hyundai, Land Rover / Jaguar (EDC16, EDC17, MD1, MEVD17, MSV/MSD (7X/8X/9X), MS45, DCM3.7, DCM6.x, PCR2.1, DCM3.4, SID201, SID208, SID803/803A, Delphi CRD1.xx DCM3.2, Delphi CRD2.xx DCM3.5, Delphi CRD3.xx, SID3xx (307, 310), EDC16 (C3, C36, CP33, C41, CP42), EDC17 (C42, C11, CP19, C84), MD1CS006, SID3xx (301, 305, 307, 309, 310), SID202-SID206, SID209-SID211, EDC17 (C10, CP65, C70), Delphi DCM 3.5, Delphi DCM 6.x, Siemens/Continental EMS22xx, Siemens/Continental EMS24xx (test), Siemens SIM210 (test), Siemens SIM28/29 (test), EDC16 (C39, CP34), DCM3.2, Siemens SIM2K, Siemens SID20x, MED17 (9.9, 9.7, 2, 8.31, 8.32)). Free: 3 removals/day.

Try DTC Remover — Free →