P0351: Ignition Coil (A) Cylinder 1 Primary/Secondary, Malfunction

Complete diagnostic information, symptoms, and potential causes

⚠️

Manufacturer-Specific Variations

This code (P0351) may have different meanings or additional parameters depending on your vehicle's make, model, and year. Always verify with your vehicle's service manual or a qualified technician before attempting repairs.

P0351
Powertrain Code

Ignition Coil (A) Cylinder 1 Primary/Secondary, Malfunction

Ignition SystemHIGH👁 Views: 65

Description

Ignition coil A cylinder 1 primary/secondary malfunction

Common Symptoms

  • Check Engine Light with cylinder 1 ignition coil malfunction
  • Cylinder 1 specific misfire detection
  • Engine vibration correlated to cylinder 1 firing
  • Rough idle from cylinder 1 combustion issues
  • Reduced engine power from cylinder 1 inefficiency
  • Poor combustion specifically in cylinder 1

Possible Causes

  • Failed ignition coil for cylinder 1
  • Open or short circuit in cylinder 1 coil wiring
  • Cylinder 1 coil connector or terminal problems
  • Wiring harness damage specific to cylinder 1
  • Coil driver circuit issues for cylinder 1
  • Engine control module cylinder 1 output failure

Diagnosis Steps

  1. Test cylinder 1 ignition coil resistance
  2. Check cylinder 1 coil circuit continuity
  3. Inspect cylinder 1 coil connector and terminals
  4. Verify wiring harness to cylinder 1
  5. Test coil driver circuit for cylinder 1
  6. Swap coil with another cylinder for diagnosis

Repair Solutions

  • Replace failed cylinder 1 ignition coil
  • Repair cylinder 1 coil circuit problems
  • Clean or replace cylinder 1 coil connector
  • Fix wiring harness damage to cylinder 1
  • Address coil driver circuit issues
  • Reset engine adaptations after repair

Prevention Tips

  • Regular cylinder-specific ignition checks
  • Protect coil wiring from heat and vibration
  • Address cylinder-specific issues promptly
⚡

Working with ECU firmware? Remove DTCs directly from firmware files

Our free Firmware DTC Remover detects and removes hardcoded fault codes directly from ECU firmware files — no software needed. Supports BMW / MINI, VAG (VW, Audi, Porsche, Skoda, Seat, Cupra), PSA (Peugeot, Citroën, DS), Mercedes-Benz, Renault / Dacia / Samsung, Ford, Kia / Hyundai, Land Rover / Jaguar (EDC16, EDC17, MD1, MEVD17, MSV/MSD (7X/8X/9X), MS45, DCM3.7, DCM6.x, PCR2.1, DCM3.4, SID201, SID208, SID803/803A, Delphi CRD1.xx DCM3.2, Delphi CRD2.xx DCM3.5, Delphi CRD3.xx, SID3xx (307, 310), EDC16 (C3, C36, CP33, C41, CP42), EDC17 (C42, C11, CP19, C84), MD1CS006, SID3xx (301, 305, 307, 309, 310), SID202-SID206, SID209-SID211, EDC17 (C10, CP65, C70), Delphi DCM 3.5, Delphi DCM 6.x, Siemens/Continental EMS22xx, Siemens/Continental EMS24xx (test), Siemens SIM210 (test), Siemens SIM28/29 (test), EDC16 (C39, CP34), DCM3.2, Siemens SIM2K, Siemens SID20x, MED17 (9.9, 9.7, 2, 8.31, 8.32)). Free: 3 removals/day.

Try DTC Remover — Free →